Router Electricity Cost 24/7: Modem and Mesh Wi-Fi Use

Quick Scenario Summary

A home network that runs around the clock is one of the few loads that never turns off. In the scenario below, a router at 12 W, a modem at 9 W, and two mesh satellites at 6 W each draw about 33 W in total. That is about 289 kWh a year, or about $52.50 per year at the U.S. average rate. A router alone at 12 W costs about $19.09 per year. The wattage values are scenario inputs, not test results. Check each device’s label, and measure the real draw with a plug-in meter before relying on the totals.

Why network gear draws power all day

Networking equipment is designed to be always on. A router waits for traffic, keeps its Wi-Fi radios and firmware running, and answers devices that check in. A modem keeps its connection to the provider active so that the link is ready when you need it. A mesh satellite does the same job as a router, repeating the signal through the house. The load is small for each device, but it does not drop to zero, because the device keeps the connection alive.

The power a device draws depends on its design, its radio activity, and the traffic it handles. A device that moves a lot of data draws more than one that is mostly idle. Devices with more radios, such as tri-band routers, can also draw more at idle than simpler models. These differences are modest, but they add up over a year, because the hours are the same for every device.

Inputs used in this guide

The calculation uses four planning inputs. They describe a common home setup, not measured results for any specific product.

– Router: 12 W, running 24 hours a day – Modem: 9 W, running 24 hours a day – Two mesh satellites: 6 W each, running 24 hours a day – Total: 33 W, which is about 0.79 kWh per day

Annual cost equals watts multiplied by 24 hours and 365 days, divided by 1,000, multiplied by the rate. The U.S. average rate is 18.16 cents per kWh, from the U.S. Energy Information Administration’s Electric Power Monthly, Table 5.6.A, for August 2026.

Setup (scenario) Power draw Energy per year Annual cost (18.16 cents)
Router only 12 W 105.1 kWh $19.09
Router and modem 21 W 184.0 kWh $33.41
Router, modem, and two mesh satellites 33 W 289.1 kWh $52.50

The table shows that each added device changes the total in a predictable way. The modem and the mesh satellites add more to the bill than the router alone, which is why a whole-home mesh system is worth counting in the total.

The same setup in four states

Electricity prices change the annual number. The table below applies the EIA August 2026 state averages from Table 5.6.A to the full setup of 289.1 kWh per year.

Location (EIA August 2026 average) Rate Annual cost, full setup
Washington 14.63 cents/kWh $42.29
United States 18.16 cents/kWh $52.50
New York 28.65 cents/kWh $82.82
California 29.75 cents/kWh $86.00

In California, the same always-on network costs about $86 per year, which is more than the U.S. average figure in the table, and more than twice the Washington figure.

Measuring the network with a plug-in meter

A short measurement gives a better answer than any table. Plug the router, the modem, and each satellite into a plug-in energy meter, one device at a time. Let each run for at least 24 hours, because some devices change their draw during the night when traffic drops. Write down the average watts that the meter shows for each device. Add the values together, then multiply by 8,760 hours a year and divide by 1,000 to get annual kilowatt-hours. The result is the figure to use in the calculator.

Measure at a typical time of day, not during a large download or a video call. A device under heavy traffic draws more, and that load does not last all year. If your household has a busy and a quiet season, repeat the measurement in each one and use the average.

Heat, placement, and airflow

Network gear produces a small amount of heat. The heat is minor for the power bill, but electronics last longer when they run within their rated temperature range. Place the router and modem where air can move around them, away from direct sun, heaters, and closed cabinets. A device in a closed cabinet can run warmer, which can shorten its life and can cause it to restart or drop the connection under load.

Place the router high and away from metal objects and thick walls where possible, because the signal reaches the rooms you use more effectively. A good placement often means fewer satellites, and fewer devices means less power.

Choosing equipment for the internet plan

The right router and modem depend on the internet speed you pay for and the number of devices in the home. A simple router with modest radios is enough for a small apartment that does not stream high-resolution video on many screens at once. A larger home with many connected devices, or with heavy use of video and gaming, may benefit from a more capable system. Oversized equipment does not make the connection faster if the plan is slow, and it can draw more power at idle.

Ask the provider whether a gateway, which combines the modem and router in one device, is supported on your plan. A gateway can replace two devices with one, which removes one standby load. Check the device’s power rating and its features before you decide, and confirm that the provider’s support terms cover the device you choose.

Wired connections and fewer devices

A wired connection to a switch or to a computer uses less power per device than a wireless link at the same speed, and it can be more stable. If a desk or a home office is close to the router, a short Ethernet cable can replace a wireless extender in that room. Removing an extender removes a device that draws power, and the wired connection often gives a steadier speed.

Keep in mind that a switch also draws power. An unmanaged switch with a few ports draws a small amount, but a larger switch can draw more. Count any switch in the total when you add up the network’s load.

Long-term costs and replacement

A network device typically lasts several years, and its replacement cost is part of the total cost of ownership. The electricity cost per year is small compared with the price of a new system, so the choice of equipment should rest on the features, the coverage, and the support, with the power draw as one factor. A device with a lower idle draw can save a little each year, which adds up over the device’s life. Compare the labels when you buy, and keep the old device’s details for reference.

Sleep and scheduled off time

Most home networks cannot be switched off during the day without disrupting the connection, so the 24-hour figure is the usual case. A few options can reduce the hours. Some routers and mesh systems support a Wi-Fi schedule that turns the wireless radios off at night while keeping the router active. Some households turn off a mesh satellite in a room that is never used, and remove it from the network. Check your router’s app or web interface for a schedule option, and test that the devices reconnect cleanly when the schedule ends.

A device’s sleep draw is not zero. Even a router that is turned off by a schedule may keep part of its hardware powered. In the scenario, a router at half its normal draw (6 W) for 12 hours a day would save about $4.77 per year. The saving is modest, but it costs nothing except a short setup step.

Why the modem matters

The modem is the device that connects the home to the provider’s network. Some households use a modem that is also a router, while others keep a separate modem and router. A combined gateway can reduce the number of devices drawing power, which lowers the total. If you are buying new equipment, compare the power ratings and features, and check whether the provider supplies a gateway that fits your needs.

Do not remove the modem to save power unless your provider and the device allow it. A modem that is switched off or unplugged will disconnect the service, and the provider’s equipment settings may need to be restored when it is switched back on.

Choosing the right mesh setup

A mesh system extends Wi-Fi coverage through satellites placed around the house. The number of satellites affects the total power draw, so add only as many as the home needs. Place each satellite where it can reach the previous node well. A satellite placed poorly may work harder to keep the signal, which can increase traffic and the power the device uses. A single router in a central spot is often enough for a small apartment, and a mesh system is most useful in a larger or multi-level home.

Practical ways to keep network power low

Count the devices. List every router, modem, extender, and satellite in the home, and add up their labeled wattage. Many people find one device they had forgotten about.

Remove unused extenders. An extender that no device uses still draws power. Unplug it or remove it from the network if you no longer need it.

Use a schedule where it fits. A nighttime Wi-Fi schedule can cut the hours of radio use without affecting the connection.

Use the right equipment. Choose a router and modem that match your internet plan and your home size. Oversized equipment can draw more power than the household needs.

Keep the device cool. Good airflow around a router and modem helps the electronics run within their rated temperature range. Avoid placing them in a closed cabinet.

Frequently asked questions

Does a router use a lot of electricity? Not much. A router at 12 W running all year costs about $19 per year at the U.S. average rate, in this scenario.

Is a mesh system much more expensive to run than a single router? It depends on the number of satellites. In the scenario, two satellites at 6 W each add about $19.09 per year to the total, on top of the router and modem.

Should I turn off the Wi-Fi at night? A schedule can do this without turning off the whole device. Check that the devices in the home do not depend on overnight connections, such as smart home systems or backups.

How do I measure my own network? Plug each device into a plug-in energy meter for 24 hours, or for a week for a more stable average. Add the results and multiply by 365 to estimate the annual figure.

What would this cost in your home?

Adjust the starting values to match your appliance and electricity plan.

Enter your values, then select Calculate my cost. Estimated energy cost in USD; fixed bill charges excluded. Month = 30 days; year = 365 days at the entered daily use. Method & limitations

Open the full electricity cost calculator

Sources and method

Annual energy equals watts multiplied by 24 hours and 365 days, divided by 1,000. Cost equals that energy multiplied by the residential rate. Rates are from the EIA Electric Power Monthly, Table 5.6.A for August 2026. Device wattages are scenario inputs. For model-specific figures, check the device label or the manufacturer’s specification sheet. The U.S. Department of Energy Energy Saver site gives general guidance on home electronics energy use. The ENERGY STAR product finder lists certified products and their published energy data.

For related comparisons, see our 24/7 router and modem cost guide and our home AI server electricity cost guide.

Written by Seon (Site Founder & Energy Data Researcher / Home Tech Reviewer). Last checked: November 22, 2026. These are calculated estimates from scenario inputs and average tariffs, not measured results.